When you do this, you will usually get a warning about a Double NAT on your network. If that is the case, you can change the setting for Connection Sharing to "Share a public IP address" Sometimes, the router that controls the ethernet network where you are connecting will only allow one device to connect. Usually allow you to connect with more than one wireless device. *Bridge Mode is the correct setting to work on other ethernet networks. Use your computer to locate the name of the wireless network that you established and see if you can log on that way and get an Internet connection. The AX will restart in 45-60 seconds and you should have a green light. Wireless Password = Your choice (write this down as well) Wireless Security = WPA/WPA2 Personal a good choice Radio Mode = 802.11n (802.11b/g compatible) will allow virtually any device to connect No check mark is needed next to "Allow network to be extended" Wireless Mode = Create a wireless network Open AirPort Utility - Click Manual SetupĬlick the Base Station tab just below the row of icons to assign a name to your AX, a device password (write this down) and adjust Time Zone settings. You have to connect to this wireless network on your computer so you can configure the AX. The AX provides a default wireless network with a name like apple network xxxxxx. You can go ahead and connect it to an available port on your router to simulate the setup at another location. Here's how to setup your AirPort Express: If you decide to get the Express, post back if you want a step by step on how to configure the device for travel. Most of the devices you list (iPhone, iPad) would not be able to connect to the 5 GHz band, so you would not need the AirPort Extreme. It's like having 2 networks in 1.īecause most cordless phones and wireless security systems also use the 2.4 GHz band, there is much more wireless interference on this band. This allows faster wireless devices to connect to the new high speed 5 GHz band while normal devices to connect to the usual 2.4 GHz band at the same time. What is the dual band mode for on the Airport Extreme? Once you have the device configured, it will retain its settings. Yes, if you have a spare port on your main router to plug into. It might work "as is" out of the box, but there would be no security on the wireless so anyone in the area could log on.Ĭan I plug it into my ethernet at home and set it up and then plug it in there in Europe and it will work? It will take a few minutes for you to assign a name to the device, establish a name for the wireless network and setup a password for the wireless. Yes, if it is handling DHCP.ĭoes it have to be configured (like when adding a router at home onto a DSL modem - ie, gateway, subnet, etc.) or is it simply a plug and play on the ethernet system? You mean "static addresses" here? Not if the Express is in Bridge Mode. Normally, you would configure the AirPort Express in "Bridge Mode" since the main router that it would connect to would already be setup to handle DHCP services. It could, but you would run into a Double NAT situation on the network. When you say up to 10 devices, are you referring to 10 computers?Ĭould be up to a total of 10 computers, iPods, iPads, iPhones or any other device that uses wireless to connect. That will get you back to the original factory defaults on the Express. You can release the reset button at this time. Keep holding the reset button until you see the amber light begin to blink more quickly. If you need to get the Express back to factory defaults to start over fresh, unplug the Express, then hold in the reset button and while you keep holding the reset button in, plug the Express back in to power. It's a bit tricky, so spend some time until you get the hang of it. Select Manage Profiles to play around with this.Ĭlick Help and enter +using profiles+ in the search box for some documentation on this. In AirPort Utility, click the Base Station Menu item (very top of the screen to the right of the Apple icon) Share Mode.when you needed to try the "share" option We may go another 2 pages on this thread □, but the AirPort Express has the ability to store up to 5 different profiles. I will have to make some notes as to how to set this all up should the need arise to Share IP Address. If the other devices can connect using wireless, it's probably not worth the hassle to take the switch and extra ethernet cables along. So would it really be worth it to carry the switch? It would make giving other users access easier but if the "main" router doesn't allow multiple IP addresses then it would be dead weight.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |